Jump to content

Search the Community

Showing results for tags 'ct2k'.

More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Welcome to CT Flier!
    • Forum News and Info
    • Polls
  • CT General Discussion
    • CT in the News
    • CT Announcements and Bulletins
    • Landing and Flying
    • Flight Instruction
    • Spot Tracker Member Links.
    • Light Sport/Sport Pilot
    • Flight Planning & Weax
    • Fly-Ins
    • Incidents
    • For Sale/Want to Buy
    • Random Thoughts
    • Trip Reports
    • Video
  • Avionics
    • General Avionics
    • Radios
    • GPS
    • Panels & Controls
    • ELT/Transponders
    • Panel & Controls
    • EFBs
    • Autopilot/Traffic Watch
    • Accessories, etc.
  • Maintenance (Remember to Work smart, Not hard)
    • General Maintenance
    • Engine/Rotax
    • Airframe/Exterior/Interior
    • Maintenance Technicians .... Anywhere in the world!
    • Maintenance Pictures and Videos
    • Fuels & Fluids
  • Dealer Forums: ....Aircraft for Sale, ....Services,.... Events,....Specials
    • Flight Design USA
    • Airtime Aviation
    • Lone Mountain Aviation
    • Premier One Aviation
    • Sonoma Flight Center


  • Admin Blog
  • Roger's Blog
  • Admin2's Blog
  • Safety Officer's Blog

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 4 results

  1. DownUnderFlier

    Junkers Chute / Harnesses CT2k

    Looking for a Junkers Chute & Rear Harness to replace the one removed from our CT2k by a previous (mis-guided) owner. Whilst I have a BRS1350HS that would fit, as the harnesses are different to the Junkers ones factory-installed inside the 'A' pillars (Junkers 40" shorter than BRS ones), I would need to remove them and re-thread the BRS ones through the 'A' pillars - Roger & Corey advised it would be very difficult to do - hence I am looking for Junkers gear ... Any leads gratefully received. David 8-)
  2. DownUnderFlier

    Chute Harness Replacement

    History: our CT2k used to have a Junkers chute installed (472.5Kg MTOW) .. the Australian rules changed and the CT2k's MTOW was raised to 544Kg .. an overly-excited compliance-frenzied mechanic removed the chute because the MTOW sticker on the instrument panel had been changed from "450Kg" to "544Kg" ... no chute is better than a 472.5Kg one, right ?! Now: have purchased a new-old-stock BRS 1350HS complete with the 4 kevlar harnesses (ex an FD MC model) and want to fit to our CT2k. Issue: the front harnesses that run inside the 'A' pillars for the Junkers chute are about 40" shorter than the BRS ones and so I want to replace those with the new, higher-capacity BRS ones - ie thread the new BRS harnesses through the 'A' pillars. Question: anyone ever removed the front harnesses ? ... would it be possible to pull through the BRS ones (attached by a cord to the Junkers ones I will be pulling out) ? Many thanks for any thoughts, wisdom, experience. David 8-)
  3. Hi guys I have a CT2k. Sometimes when I deploy flaps, I hear a creaking/knocking sound. It’s just once or twice and not constant. It doesn’t happen on the ground? Is this normal? I was wondering if it is just the airframe and if anybody else has had this ? My other question is that I recently had my pilot side left rudder pedal replaced by my engineer. This has inadvertently resulted in my stick coming back a little bit more and my stabiliser deflecting more. I’ve checked the deflections and they are good. I previously had difficulty getting a pronounced flare but it is much easier now that I can get the stick back further. My question is what has caused this change? My engineer says he didn’t adjust anything on the stabiliser.
  4. salvavidal

    CT2K videos

    Hello, i would like to share with you my youtube channel, you can find a lot of videos recorded and edited by my self. I hope you enjoy. I let here channel url: https://www.youtube.com/channel/UC5RBXJ7k0MH9IBQBKw6e6qQ